2008 CHEVY EQUINOX INSTALL
2008 CHEVY EQUINOX SOFTWARE
2008 CHEVY EQUINOX LICENSE

When placing the pump onto the engine be sure that you have the pumps drive shaft held in place and So that it does not shift during installation. There should be two pins which hold the pump in place

2008 CHEVY EQUINOX INSTALL

Install the oil pump onto the bottom of the engine block right onto the rear most main cap. After preparing the contact surfaces carefully Both surfaces should be cleaned and preped prior to installing. When installing the oil pump be sure to use the proper sealant around the pump base if neccessary to ensure that oil pressureĭoesn't drop due to leakage. To ensure all pistons move smoothly in and out of their cylinders and nothing binds.Ĭhevy Equinox 3.4L Connecting Rod Torque Specs : 15 ft-lbs + 75° Rod bolts to 15 ft-lbs and then an additional 75 degree turn for each bolt. Once installed you can match the connecting rod caps with the correct rods and start to torque the connecting Or mark is facing the front of the engine and that you don't scratch the cylinder. The piston can now be lowered into the cylinder, make sure the dot Once the rings have been installed you can now fit the connecting rod bearings into the end capsĪnd lube them up with oil or lithium grease. Each ring manufacturer is different so be sure to check for your The instructions given with the new rings. Positions, this can be determined by looking at Make sure to put the correct rings in the correct Not to stretch the rings or break them during installation. To install the pistons and connecting rods you must first install the piston rings into each piston. Unlimited Year/Model Ford or Universal Creditsįalcon BA, BF, FG, FGX, Territory models (Including A6 TCM support)Įxcursion 6.0 Diesel (Including FICM support)įiesta ST 1.6 EcoBoost (non-USDM) (MED17.0.1) (2)įiesta ST 1.5 EcoBoost (non-USDM) (TC-277)į-Series 4.6, 5.4 (Except old body style and Lightning)į-Series 6.Bottom End Torque's Main Cap Bolts Torque Spec 37 ft-lbs + 75° Connecting Rod Bolts Torque Spec 15 ft-lbs + 75° Oil Pump Mounting Bolt Torque Spec 30 ft-lbs Oil Pan Torque Specs 18 ft-lbs Oil Pan Drain Plug Torques 18 ft-lbs Intake Manifold and Fuel Rail Torque Spec Intake Manifold Bolts Torque Spec (Upper) 18 ft-lbs Intake Manifold Bolts Torque Spec (Lower) 10 ft-lbs Fuel Rail Torque Specs 8 ft-lbs Spark Plugs Torque Specs 11 ft-lbs Throttle Body Torque Specs 21 ft-lbs Ignition Coil Module Torque Spec 18 ft-lbs Water Pump & Pulley Torque Specs Water Pump Bolts Torque Specs 8 ft-lbs Water Pump Pulley Torque Specs 18 ft-lbs Crankshaft Pulley Torque Spec 52 ft-lbs + 85° Drive Belt Tensioner Bracket Torque Spec 40 ft-lbs Drive Belt Tensioner Bolt Torque Spec 37 ft-lbs Belt Idler Pulley Bracket Torque Spec 22 ft-lbs Belt Idler Pulley Bolt Torque Spec 37 ft-lbs Motor Mount (Engine Side) Torque 59 ft-lbs Motor Mount (Frame Side) Torque 35 ft-lbs Power Steering Pump Torque Spec 25 ft-lbs Alternator Bracket Torque Spec 37 ft-lbs Unlimited Year/Model Dodge or Universal Credits Single Vehicle Dodge or Universal Credits Silverado 5.3, 6.2 (needs ECU unlocked) (2) Unlimited Year/Model GM or Universal CreditsĬobalt 2.0, 2.2, 2.4 (05-06 2.2 Not Supported)

Vehicles that are only supported by MPVI2, MPVI2+, and MPVI3 interfaces are identified below by a (2) after the vehicle model type.Ī3 2.0L TFSI (8P, 8V) (MED9.1, MED17.5) (2) If your vehicle is a hybrid or has a physically different VCM/ECM/PCM than it originally came with, your vehicle might not be supported. Our product is designed to work for vehicles straight off the showroom floor with stock calibrations.

2008 CHEVY EQUINOX LICENSE

Here is what License Activation looks like.

2008 CHEVY EQUINOX SOFTWARE

You do not need to know which license method you prefer at the time of your order, but you will be prompted by the software for your selection when you tune the vehicle for the first time. Some models offer TCM, FICM, FSCM, and CCM tuning at an additional cost.

Please note that the pricing models below are for ECM/PCMs only.

Unlimited vehicle group licenses will allow you to tune all vehicles that fall under that vehicle group category.

Year/Model type licenses will work on an unlimited number of vehicles of that particular model and year.

Replacing the ECM/PCM/VCM will require re-licensing.

Each single vehicle license is tied to the interface used to license the ECM/PCM/VCM.

Single vehicle licenses will work only with the specific vehicle’s ECM/PCM/VCM you have locked the license to.

2008 chevy equinox